LED drivers and LED dimming: TRIAC, 0-10V, DALI and wireless, and how not to get it wrong

Home > Home lighting design > LED drivers and LED dimming: TRIAC, 0-10V, DALI and wireless, and how not to get it wrong

The article

In short: every LED fixture needs an LED driver, a power supply that converts mains voltage into the current the LED needs, and the driver determines whether and how the fixture can be dimmed. There are four main methods: phase dimming (TRIAC), which works on the existing wiring but is sensitive to the match between dimmer and driver; 0-10V, analogue with two control wires; DALI, digital with an address for each fixture; and wireless, such as Casambi. Choose one method for each circuit, make sure all the fixtures on it support it, and decide before the electrician starts running the wiring.

Dimming is the simplest way to turn a lit room into a pleasant one. But with LED, more than with old-style bulbs, dimming is a matter of compatibility: a dimmer, a driver and a fixture that don’t speak the same language produce flicker, buzzing, light that doesn’t switch off completely, or fixtures that dim at different rates. The guide explains the terms and the methods, so that you can ask the right questions.

What is a driver

LED works on direct current at low voltage, while the home has a 230-volt alternating-current mains supply. The driver converts between them and keeps the LED stable. There are two main types:

Constant current (CC) Constant voltage (CV)
What is fixed The current, for example 350, 500 or 700 milliamps The voltage, for example 12, 24 or 48 volts
Feed LED modules for spotlights and fixtures LED strips and low-voltage tracks
Connecting several fixtures In series, within the driver’s voltage range In parallel, up to the maximum power

You can see this on the product pages. For example, Flexalight spotlights such as Kol list a supply current of 350 or 500 milliamps, which means a constant-current driver. A Catellani & Smith fixture such as More lists a 12-volt DC transformer, which is not included. This figure determines which driver is needed, and one type must never be swapped for another.

Built-in or separate driver

In many fixtures, and in all household bulbs, the driver is built in. In recessed spotlights, architectural fixtures and LED strips it is separate, and then a place has to be planned for it: ventilated, accessible for maintenance and not too far from the fixture, because at low voltage a long cable causes voltage drop.

How large

With a constant-voltage driver, a common rule is not to use more than about 80 percent of its rated power. With a constant-current driver, check that the current matches the fixture exactly, and that the sum of the voltages of the fixtures in series is within the range the driver can deliver.

The four dimming methods

1. Phase dimming (TRIAC and phase-cut)

The dimmer “cuts” part of the voltage wave. The advantage: it works on the two existing wires and replaces an ordinary switch. There are two types: cutting at the start of the wave (Leading Edge, the classic TRIAC) and cutting at the end of the wave (Trailing Edge), which is usually better suited to LED and quieter.

The drawbacks: sensitivity to the match between the dimmer and the driver, a minimum load (a dimmer designed for incandescent bulbs may not work well with two small LED spotlights), and sometimes a limited dimming range. Suitable for the home and for a renovation where you do not want to add wires. For example, TRIAC dimming is specified for the Mamì pendant lamp by Penta.

2. 0-10V and 1-10V

Two extra wires, in addition to the power wires, carry a control signal to the driver: 10 volts is full light, and the low voltage is minimum light. With 1-10V the driver supplies the signal, and with 0-10V the controller. Dimming is smooth and stable, but the whole circuit receives the same command. Common in offices and shops.

3. DALI

DALI (Digital Addressable Lighting Interface) is a digital system on two control wires. Each driver has an address, up to 64 on one line, and you can control each fixture or group separately, save scenes (“dinner”, “cleaning”) and receive fault reports. DALI-2 is the updated generation that ensures better compatibility between makers, and DT8 is a type of DALI that also controls the colour temperature. For example, for the Manta fixture by Terzani, the dimming options listed are DALI, 0-10V and 1-10V.

4. Wireless dimming

Systems such as Casambi (Bluetooth-based) or Zigbee add a wireless component to each fixture or driver, and are controlled with an app, a wireless push-button or through a smart home system. The great advantage is that no control wires are needed, so they suit renovations. Makers such as Occhio have also developed their own control: switching on and dimming with hand gestures near the fixture, and Bluetooth control.

Quick comparison

Method Additional wiring Control of each fixture separately Dimming quality Suitable for
Phase (TRIAC) No No Varies accordingly Home, renovation
0-10V 2 wires No Good Offices, shops
DALI 2 wires Yes Very good Large homes, hotels, retail
Wireless No Yes Very good Renovation, smart home

Scenes and smart home

The great advantage of DALI and the wireless systems is scenes: one press that sets the room to a particular mode. For example “Dinner”: the light above the table at 70 percent, the spotlights in the living room at 30 percent, the wall lights on and the light in the kitchen off. Or “Night”: only the corridor lighting at 10 percent. In a smart home, the lighting system connects to the central controller through a gateway, and then the lighting can be combined with shutters, sensors and timers. If this is in the plan, the method and the components have to be decided before the wiring is laid, making sure that all the drivers chosen are compatible with it.

Flicker: the problem you cannot always see

Some drivers dim by switching on and off very rapidly (PWM). When the frequency is low, the eye does not always see it, but the brain picks it up: some people feel tired or get a headache, and the phone camera shows stripes. Quality drivers dim at a very high frequency or by continuous current reduction, and are specified as “Flicker Free”. There are also professional recommendations for flicker limits, for example IEEE 1789. A simple test: film the dimmed fixture with the phone camera and see whether stripes appear.

Common faults and what to do

Fault Likely cause What to do
Flicker at low output Mismatch between dimmer and driver, or a cheap driver A dimmer suitable for LED, setting the minimum on the dimmer, a quality driver
Buzzing Leading Edge dimmer with an LED load Switching to a Trailing Edge dimmer
The light does not switch off completely Leakage current through the dimmer A dimmer with a neutral connection, or a load resistor as instructed by the manufacturer
Fixtures dim at different rates Different drivers on the same circuit Fixtures from the same series and the same driver on each circuit
Jump from low light to off Limited dimming range A driver that dims to a low percentage, or a digital system

What to ask when buying a light fixture

  • Is the fixture dimmable, and with which method?
  • Is the driver included, and if not, which driver suits it (current or voltage, and how much)?
  • Down to what percentage does the fixture dim without flicker?
  • Is there a version with DALI or with a wireless component, should it be needed later?
  • Where is the driver installed, and what is the maximum distance from it to the fixture?

How to plan properly

  • Decide in advance which circuits will be dimmed: usually the living room, dining area, bedroom and accent lighting.
  • Choose one method for each circuit, and make sure every fixture on it supports it. Decorative fixtures from different makers sometimes come with different methods, so it is worth checking each one on its product page.
  • If in doubt, run control wires: two extra wires in the conduit cost almost nothing during a renovation, and let you switch to DALI or 0-10V later.
  • Ask about a separate driver: if the fixture comes without a driver, who chooses it, where it will be installed, and what it supports.
  • Test before the ceiling is closed: connect, switch on, dim all the way down and film it on your phone.

The colour temperature can also change with dimming (Dim to Warm) or by control (Tunable White). On this, see Colour temperature and colour rendering. For overall planning: How to plan lighting for a whole apartment. And for low-voltage tracks, where the driver is part of the design: Magnetic track and standard track. General information on LED bulbs is also available in the guide to choosing an LED bulb.

Questions and answers

Can any LED fixture be dimmed?

No. The fixture and its driver have to support dimming, and the specific method you have chosen. The product page usually states the type of dimming, for example TRIAC, 0-10V, DALI, or ‘not dimmable’.

Why does an LED bulb flicker when it is dimmed?

Usually because of a mismatch between the dimmer and the driver, a load below the dimmer’s minimum, or a cheap driver that dims with low-frequency flicker. The solution is a dimmer suited to the type of load, a quality driver, or a switch to a different dimming method.

What is the difference between DALI and 0-10V?

Both need two extra control wires. With 0-10V the whole circuit receives the same command. DALI is a digital system in which each fixture has an address, so each fixture or group can be controlled separately, scenes can be saved and faults are reported.

What is the difference between a constant current driver and a constant voltage driver?

A constant-current driver, for example 350 or 500 milliamps, powers the LED modules of spotlights and fixtures. A constant-voltage driver, for example 12 or 24 volts, powers LED strips and low-voltage systems. They must not be swapped: the wrong driver can destroy the LED.

Does dimming save electricity?

Yes. With LED, dimming lowers electricity consumption roughly in proportion to the drop in output, and usually also extends the life of the fixture.

For architects and designers
Skip to content

Sent successfully

Thank you. We have received your details and will get back to you soon.

Book a meeting